Recent Posts

| Forums | Topics

Page 2 / 3 Prev Next

Topics with their latest replies in reversed order
	How to define SPI pin in AK Board 0.5.1 11? By KevinGuo 1 month ago \| Last Post: 2 weeks ago Forum Microcontroller Firmware (C++)
	@KevinGuo The SPI interface isn’t actively used ... 2 weeks ago By Shanp... While using the AK Board 0.5.1 11, I noticed that ... 1 month ago By Kevin...
	The selection issues of R13 and R15 By wuyang 3 weeks ago \| Last Post: 2 weeks ago Forum PCB - Electrical
	@wuyang Here's the JLCPCB part number we used in... 2 weeks ago By Shanp... We were unable to find matching parts for resistor... 3 weeks ago By wuyan...
	The selection issue of the D1 electronic component By wuyang 2 weeks ago \| Last Post: 2 weeks ago Forum PCB - Electrical
	@wuyang We recently ordered a new batch of PCBs ... 2 weeks ago By Shanp... Hello, regarding the D1 electronic component in th... 2 weeks ago By wuyan...
	PCB Parts By OpenExo Team 2 months ago \| Last Post: 3 weeks ago Forum PCB - Electrical
	@shanpu-fang Hello, the YAGEO resistor model MFR1W... 3 weeks ago By wuyan... For the 470-ohm resistors (R13 and R15), we used t... 2 months ago By Shanp... The P78E05-1000 DC-DC converter, based on the spec... 2 months ago By Shanp...
	Sorry the forum is so slow right now. By Zachary Lerner 2 months ago \| Last Post: 3 weeks ago Forum Announcements
	The forum should be faster now. Leave a reply if n... 3 weeks ago By Zacha... We're actively working on making the forum faster. 2 months ago By Zacha...
	Ask for the specific wiring information for sensors, synchronization LEDs, emergency stop, RESET, etc. on the AK Board 0.5.1 11? By KevinGuo 1 month ago \| Last Post: 3 weeks ago Forum PCB - Electrical
	@Shanpu Fang Thank you for your response regardin... 3 weeks ago By Kevin... @KevinGuo The E-Stop functionality was originally... 3 weeks ago By Shanp... Certainly, the torque sensor is a Wheatstone bridg... 4 weeks ago By conno... view all posts
	Are changes needed to be made to BOM for ankle if using AK80 motor instead? (1 viewing) By Delta 4 weeks ago \| Last Post: 4 weeks ago Forum Motors and Sensors
	Thanks for your great question, Delta! It depends ... 4 weeks ago By Zacha... I have a few questions regarding the Ankle BOM. ... 4 weeks ago By Delta
	Is the motor torque sensor a mandatory requirement? By KevinGuo 1 month ago \| Last Post: 4 weeks ago Forum Motors and Sensors
	We are working on a wiki page to better describe o... 4 weeks ago By Zacha... Hello @KevinGuo To trouble shoot your teensy pro... 1 month ago By conno... I tried uploading OpenExo.ino directly to the Teen... 1 month ago By Kevin...
	Is there any detailed documentation that describes the specific wiring information for sensors, synchronization LEDs, emergency stop, RESET, etc. on the AK Board 0.5.1 11? By KevinGuo 1 month ago \| Last Post: 4 weeks ago Forum PCB - Electrical
	Hello Kevin, I believe that the mentioned compon... 4 weeks ago By conno... The following document is already very well writte... 1 month ago By Kevin...
	After uploading the compiled OpenExo.ino to the Teensy 4.1, the serial monitor continuously restarts. By KevinGuo 4 weeks ago \| Last Post: 4 weeks ago Forum Microcontroller Firmware (C++)
	1. In ExoCode.ino, I enabled HEADLESS mode and com... 4 weeks ago By Kevin... @Zachary Lerner I haven't connected the Python G... 4 weeks ago By Kevin... @KevinGuo are you using the Python GUI? If so, are... 4 weeks ago By Zacha... view all posts

Page 2 / 3 Prev Next